Free tool · no signup
Room acoustics calculator: reverberation, room modes and isolation
Type your room's dimensions and what is on the floor, the walls and the ceiling. It tells you how long it rings in each frequency band, which notes the room resonates at, how many square feet of treatment you are short, and at what frequency a double wall resonates.
The coefficients come from 245 materials with real manufacturer data sheets, 77 of them sold in the United States, each one citing its source. No generic table averages with nobody behind them.
Your room
Inside dimensions, wall to wallThe calculation treats the room as empty: furniture, clothes, curtains and the people in it all bring the real figure down, mostly in the mids and highs. If you have curtains or a rug, model them on the floor or the walls to get closer. 77 materials with absorption curves from manufacturer data sheets, all of them sold in the United States. This one was tested to ASTM C423 Mounting Type A.
Reverberation time
1232 ft³ · 708 ft² of surfaceRT60 at 500 Hz
1.60 s
Target
0.20–0.30 s
Bands on target
0 of 6
This room is reflective (mean α ≤ 0.20); Sabine and Eyring nearly agree, so Sabine is used. Target per EBU Tech 3276 — Tm = 0.25·(V/100)^(1/3).
EBU would ask for 0.18 s, but that standard is written for large reference listening rooms: in a 1232 ft³ room it means covering close to half the surfaces and leaves the room dead. 0.25 s is used instead, which is what small control rooms actually aim for.
At 125 Hz up to 0.3 s above target is allowed: no standard asks for the same decay time in the bass as in the mids, because bringing the bass down costs thickness, not square footage.
How much treatment is missing
Sized at 500 Hz, at the top of the rangeYou are short 150.1 ft² of Owens Corning Fiberglas 703 51 mm (Owens Corning), which is about 19 panels of 2 × 4 ft.
The calculation subtracts what the covered wall was already absorbing: adding the panel without subtracting the surface underneath is the standard way to overbuy. It also sizes against the top of the range rather than the middle, because aiming at the middle asks for almost twice the material and leaves the room dead — hanging one more panel later is always easier than bringing an over-treated room back to life.
| Band | Current absorption | Needed | ft² short |
|---|---|---|---|
| 125 Hz | 0.9 | 9.4 | 906.0 |
| 250 Hz | 1.8 | 14.0 | 199.6 |
| 500 Hz | 3.5 | 18.7 | 150.1 |
| 1 kHz | 8.8 | 18.7 | 96.7 |
| 2 kHz | 11.0 | 18.7 | 85.2 |
| 4 kHz | 11.8 | 16.0 | 48.6 |
Room modes
Transition at 357 HzBelow 357 Hz this room has no even sound field: individual modes take over, and that is where the bass sounds different depending on where you sit. Above it, average RT60 describes what happens well enough.
The proportions fall inside Bolt's recommended area and spread the low-frequency modes well.
Proportions 1.75 : 1.38 : 1 (length : width : height).
- Stacked modes: Two axial modes 4.8% apart (153.5 and 160.8 Hz): that note will sound louder and ring longer than its neighbours.
Double wall: what frequency does it resonate at?
Mass-spring-massTwo leaves separated by air make a spring. Below its resonance frequency a double wall isolates worst than a single layer would. If that frequency falls inside the music, the wall gives back exactly what you were trying to contain.
60 Hz
f0 at 60 Hz: acceptable for speech and for music without heavy sub-bass, but a kick drum will find it.
With the cavity left empty it would rise to 84 Hz: filling it with mineral wool is not optional — it is what brings the resonance down.
This is as far as a quick calculation goes
This calculator assumes absorption is evenly spread. It does not look at where you sit, where the speakers are, or where your neighbour's noise gets in. That is a diagnosis, and that is what the report does.
How this is calculated, no mystery
Reverberation time is how long sound takes to drop 60 dB after the source stops. Sabine's formula estimates it as RT60 = 0.049 · V / A, where V is the volume in cubic feet and A is total absorption in sabins: every surface multiplied by its coefficient in that frequency band. In metric the same formula reads RT60 = 0.161 · V / A, with V in cubic metres. Because the coefficient changes with frequency, so does the result — which is why you get six numbers here and not one.
Sabine assumes sound is spread evenly through the room. In a small, well-treated room that stops being true and the formula returns a longer time than reality. When the average coefficient goes above 0.20, this calculator switches to Eyring, which corrects that bias. It tells you which one it used and why, instead of handing you a number and staying quiet.
In the bass neither formula describes what actually happens, because down there geometry rules: the modes. The boundary is the Schroeder frequency, f = 2000·√(RT/V). In a typical studio room it lands between 100 and 200 Hz, and below that an average means nothing.
What this calculator cannot know
It is for sizing the problem and understanding it, not for signing off a build. It assumes absorption is spread evenly, and it almost never is: putting all the material on one wall gives the same number in the formula and a very different result in your ears. It also does not know where you sit or where the monitors are, which is what decides which modes hit you and where the early reflections land.
And it says nothing about noise getting in or out: that is isolation, a different problem solved with mass, airtightness and decoupling, not with panels. The double wall block above is only the first question of that other problem.
Frequently asked questions
Will acoustic panels stop my neighbour hearing me?
No, and this is the most expensive misunderstanding in the whole field. Panels change how the room sounds on the inside — that is treatment. Keeping sound from getting in or out is isolation, and it is solved with mass, airtightness and decoupling, not with foam. A room covered in panels can still be perfectly audible next door.
What RT60 should a home studio have?
For a small control or mix room, roughly 0.2 to 0.3 seconds, and — more important than the number — reasonably even across bands. A room that measures 0.25 s at 1 kHz and 0.7 s at 125 Hz is not a 0.25 s room: it is a room with a bass problem that a single average number hides.
How many acoustic panels do I need?
It depends on the volume of the room, what the surfaces already absorb and what you use the room for — which is what this calculator works out. Be wary of rules of thumb like 'cover 40% of the walls': the same percentage in two rooms with different floors gives completely different results.
Is NRC enough to choose a material?
No. NRC averages the 250, 500, 1000 and 2000 Hz bands and ignores 125 Hz entirely, which is precisely where a small room's problems live. Two materials with the same NRC can behave very differently in the bass. Look at the full octave-band curve, and at the mounting it was tested with.
Does the mounting really change the numbers that much?
Yes. The same panel flat against the wall and spaced 100 mm off it are two different curves, and the difference shows up mostly in the low mids, where it matters. A data sheet that does not state the mounting is giving you half the information.
Want someone to look at your room?
This sizes the problem. A remote design turns it into a plan: scale drawing, every panel specified, materials list and build order, delivered in four business days.
See the design services →